The USB cable driver offered by Baofeng is buggy and the programming software made by the manufacturer is, for all intents and purposes, junk. Fortunately, there are other options available, and once properly installed, they are actually quite good. You just need to know where to find these options and how to install them properly. VIP Software is designed for Windows Operating Systems. Mac OSX and Linux users are recommended to use a Virtual Machine to run the VIP Windows programming software. For easier initial frequency programming, copy and paste, and importing frequency files from previous radios - you may want to consider using the CHIRP Programming Software found. VIP Software is designed for Windows Operating Systems. Mac OSX and Linux users are recommended to use a Virtual Machine to run the VIP Windows programming software. For easier initial frequency programming, copy and paste, and importing frequency files from previous radios - you may want to consider using the CHIRP Programming Software found. Programming software. Use eldoLED's freely downloadable software for LED driver programming (FluxTool) or for creating standalone show sequences (ShowMaster DMX).
Here we are providing another amazing software for your Windows, Linux, and Mac. The Baofeng UV 5R Programming software chirp is available here on this page to download you get your free software from below links just click on the given link to start the download. This page provides general tips and troubleshooting for the Baofeng UV-5R, UV-82, The UV-5R is the base model for a lot of variants, so this page will apply to many more people than just those with that specific badge on their radio. This information is a summarized version of the Miklor page on the subject. Go there for more detailed information.
List Of Programming Software
Related Keywords for Baofeng cable chirp software:
Baofeng UV 82 programming software
Baofeng USB driver download
Baofeng UV-5R firmware update
Baofeng bf 888s software
There is, in most cases, almost no actual difference between the variants, which is very confusing for customers. It's difficult to find a genuine driver and cable. Here on this page, we provided the original link of the genuine programming cable driver you can find it easily at the end of this post These are the devices which support Baofeng software chirp except F-11.
997-S:
B-580T
BF-E500S
BF-F8/BF-F8+
BF-F9
BF-UVB2 Plus
F-11: Import Communications
FF-12P
GT-3/GT3 MK2
RH5R:
RT-5R/RT-5RV:
RT5 with 2 power levels:
UV-5R V2+
UV-5R+/UV-5R+Plus
UV-5R2
UV-5RA/UV-5RA+/UV-5RAX+
UV-5RAX (2M/1.25M)
UV-5RB
UV-5RC/UV-5RCX+
UV-5RCX (2M/1.25M)
UV-5RD
UV-5RE/UV-5RE Plus
UV-5RG
UV-5RK
UV-5RQ
UV-5RS
UV-5RT
UV-5RU
UV-5S
UV-5X
UV-920
UV-B2 Plus
UV-B3 Plus
UV-E5/UV-E5 MK2:
ZT-V8/ZT-V8A/ZT-V8A+
Features of Baofeng Programming software:
XLT Painless Programming Cable
Model: RPC-K1-UF.
Support all Windows versions.
A true plug-n-play solution!
Genuine FTDI chip
No legacy or third-party drivers required
Length: 3ft. (91.44cm)
Works with Baofeng UV-5R, UV-B6, BF-F9, and other Baofeng radios, Kenwood two-pin radios, Wouxun, Puxing, Weierwei, Quansheng, and other two way radios with a Kenwood connector.
Some companies use cloned programming software with an original stamp always check the cable before use. Always try to use genuine cable driver or programming cable don't use cheap cables. If you don't know how to use this software then read the following steps carefully then you will be able to install this software successfully on your computer or laptop. After reading this information you still unable to install Baofeng programming software on your PC then let us know ur problem through comments below in the comments section.
Software Driver Programming
How to Use Baofeng USB Programming Cable:
First of all on your computer and turn off your radio.
Download the USB programming cable driver from below link.
Locate the correct USB programming driver for your operating system. You can download the Prolific driver for Windows, Mac, and Linux from here.
Install the USB Driver cable on your computer.
Plug the USB programming cable into the USB port on your computer. Plug the other end of the cable into your radio and turn it on.
Run the CHIRP Programming Software. Click Go to Radio on the menu bar and choose Download From Radio. Choose the COM Port number for the USB cable, the Vendor (Baofeng) and the model of the radio (such as UV-5R) from the drop-down lists in the pop-up box. Your radio should be connected to the computer and CHIRP should now be able to communicate with it.
Now you will be able to use the new programming cable driver.
The download links given here are the latest free and safe. If any link doesn't work properly or any link is broken then tell us through comments we will update the post and will give you the most recent links.